Difference between revisions of "Published Papers"

From Hyrel3D
Jump to: navigation, search
(Count)
(Published in 2022)
Line 15: Line 15:
 
==== Published in 2022 ====
 
==== Published in 2022 ====
  
* [https://www.spiedigitallibrary.org/conference-proceedings-of-spie/12042/120420W/Additively-manufactured-unimorph-dielectric-elastomer-actuators-with-ferroelectric-particles-for/10.1117/12.2613128.short?SSO=1 Additively Manufactured Unimorph Dielectric Elastomer Actuators with FerroelectricPparticles for EnhancedLlowVvoltageAactuation] by a team from the [https://daytonabeach.erau.edu/college-engineering/aerospace Aerospace Engineering Department of Embry-Riddle Aeronautical Univeristy]
+
* [https://www.spiedigitallibrary.org/conference-proceedings-of-spie/12042/120420W/Additively-manufactured-unimorph-dielectric-elastomer-actuators-with-ferroelectric-particles-for/10.1117/12.2613128.short?SSO=1 Additively Manufactured Unimorph Dielectric Elastomer Actuators with Ferroelectric Particles for Enhanced LowVvoltage Actuation] by a team from the [https://daytonabeach.erau.edu/college-engineering/aerospace Aerospace Engineering Department of Embry-Riddle Aeronautical Univeristy]
  
 
* [https://mdpi-res.com/d_attachment/polymers/polymers-14-01351/article_deploy/polymers-14-01351-v2.pdf Innovation in Additive Manufacturing Using Polymers: A Survey on the Technological and Material Developments], a review of "the most recent advances from technological and physico-chemical perspectives to improve several remaining issues in polymeric materials’ additive manufacturing", by a team from [https://www.uss.cl/ Universidad San Sebastián], [https://www.utem.cl/ Universidad Tecnológica Metropolitana, Santiago], and [https://www.csic.es/en/investigation/institutes-centres-units/institute-polymer-science-and-technology Instituto de Ciencia y Tecnología de Polímeros-Consejo Superior de Investigaciones Científicas], Chile
 
* [https://mdpi-res.com/d_attachment/polymers/polymers-14-01351/article_deploy/polymers-14-01351-v2.pdf Innovation in Additive Manufacturing Using Polymers: A Survey on the Technological and Material Developments], a review of "the most recent advances from technological and physico-chemical perspectives to improve several remaining issues in polymeric materials’ additive manufacturing", by a team from [https://www.uss.cl/ Universidad San Sebastián], [https://www.utem.cl/ Universidad Tecnológica Metropolitana, Santiago], and [https://www.csic.es/en/investigation/institutes-centres-units/institute-polymer-science-and-technology Instituto de Ciencia y Tecnología de Polímeros-Consejo Superior de Investigaciones Científicas], Chile

Revision as of 13:44, 2 May 2022

Below is a list of published works citing Hyrel equipment.

Count

329 documents as of 2 May, 2022.

Non-Traditional Manufacturing

Including Antennas, Sensors, Inductors, and Circuits; Combined Manufacturing Techniques; Electro-Spinning or Electro-Melt-Spinning or Melt Electro-Writing (MEW); also printing with Embedded Fibers and combining FDM with DIW or MEW.

Published in 2022

Published in 2021

Published in 2020

Published in 2019

Published in 2018

Published in 2017

Published in 2016

Published in 2015

Unheated or Chilled Reservoir Printing (DIW)

Also known as Robocasting or DIW, Direct Ink Writing.

Published in 2022

Published in 2021

Published in 2020

Published in 2019

Published in 2018

Published in 2017

Published in 2016

Published in 2015

Published in 2014

Heated Reservoir Printing (DPE, HME)

Also known as DPE (Direct Powder Extrusion) or HME (Hot Melt Extrusion).

Published in 2022

Published in 2021

Published in 2020

Published in 2019

Published in 2018

Published in 2017

Filament Printing (HME, FFF, FDM)

Also known as HME (Hot Melt Extrusion), FFF (Fused Filament Fabrication), or FDM (Fused Deposition Modeling).

Published in 2022

Published in 2021

Published in 2020

Published in 2019

Published in 2018

Published in 2017

Published in 2016