Difference between revisions of "Settings"

From Hyrel3D
Jump to: navigation, search
(Created page with "== '''Loading Settings''' == Last, you should load/reload your settings: # Setings > Printer. # Load Settings from File (find your custom file, or the most recent one named ...")
 
(Printer Settings)
(46 intermediate revisions by the same user not shown)
Line 1: Line 1:
== '''Loading Settings''' ==
+
{| align="right"
 +
| __TOC__
 +
|}
  
Last, you should load/reload your settings:
+
== '''Printer Settings''' ==
  
# Setings > Printer.
+
Last, you may need to (re)load your settings; there are several screens, detailed below.
# Load Settings from File (find your custom file, or the most recent one named for your model of printer.).
+
 
# Set or change color selections as desired on the last tab.
+
Before doing these steps, please see if the settings you already have loaded will work!
# Flash Motion Settings.
+
 
# Apply.
+
To load a configuration file, do the following:
# Write to local file with your custom name, as a backup.
+
 
# OK.
+
# Go to Setings > Printer.
 +
# Click "Save Settings To File" with your custom name, today's date, and "ASFOUND" as a backup
 +
# Go see if everything works. If not:
 +
# Click "Load Settings from File" - see file names below
 +
# Make any customization you like
 +
# Click "Flash Motion Settings"
 +
# Click "Apply"
 +
# Click "Save Settings To File" with your custom name, today's date, and "WORKING" as a backup
 +
# Click "OK"
 +
 
 +
These steps are performed in this video: https://www.youtube.com/watch?v=N1HZOvWKqs8
 +
 
 +
Note that after flashing, or upon startup, you will be required to home the X and Y axes before other moves are allowed; on the EHR, you will also have to home the Z. This is so that the printer knows where you are and whether or not it is safe to move the amount you tell it to. If you unlock your motors or press the emergency stop button, you should home the X and Y axes again before making other movements (also Z on EHR).
 +
 
 +
While each printer is shipped with tested, verified settings, you are welcome to customize your unit. For example, a second yoke will reduce your max travel in the X; an auxiliary build plate may have smaller dimensions; tall Hydras will have more travel in the Z; and you will probably want to limit your travel if you've added a vise or chuck.
 +
 
 +
'''The latest Printer Settings files are available at [http://hyrel3d.net/downloads/repetrel/Printer_Settings_2019.12.05.rar http://hyrel3d.net/downloads/repetrel/Printer_Settings_2019.12.05.rar]''' Note that these are included in the latest v4 Repetrel download.
 +
 
 +
=== '''File Names''' ===
 +
 
 +
When you select "Load settings from File" (or "Switch Printer Type" from the menu), here's what the file names mean:
 +
 
 +
{| border="1" class="wikitable" style="width: 50%;"
 +
|+ Printer Files
 +
! style="width: 20%;" | File Name
 +
! style="width: 20%;" | Model/Version
 +
! style="width: 20%;" | Special Notes
 +
|-
 +
| 16AS
 +
| 16A Standard
 +
| Standard
 +
|-
 +
| 16AS_2Y
 +
| 16A Standard
 +
| 2nd Yoke
 +
|-
 +
| 16AS_2Y_45A
 +
| 16A Standard
 +
| 2nd Yoke, 4th/5th Axis
 +
|-
 +
| 16AS_45A
 +
| 16A Standard
 +
| 4th/5th Axis
 +
|-
 +
| 16AT
 +
| 16A Tall
 +
| Standard
 +
|-
 +
| 16AT_2Y
 +
| 16A Tall
 +
| 2nd Yoke
 +
|-
 +
| 16AT_2Y_45A
 +
| 16A Tall
 +
| 2nd Yoke, 4th/5th Axis
 +
|-
 +
| 16AT_45A
 +
| 16A Tall
 +
| 4th/5th Axis
 +
|-
 +
| 30M_ESR
 +
| 30M and ESR
 +
| Standard
 +
|-
 +
| EHR_diffXY
 +
| EHR
 +
| *early models
 +
|-
 +
| EHR_standard
 +
| EHR
 +
| Standard
 +
|-
 +
| ESR_30M
 +
| ESR, 30M
 +
| Standard
 +
|-
 +
| 30M_ESR
 +
| 30M, ESR
 +
| (same as above)
 +
|-
 +
| fadal429
 +
| Fadal CNC
 +
| Standard
 +
|-
 +
|}
 +
 
 +
== '''Programs''' ==
 +
 
 +
In Repetrel, go to the Programs tab, and double click in each text field, pointing the applications to their respective executable files under <code>C:/EcosystemApps</code>. See the table below for the proper locations. Note the new location for the Slic3r install; Slic3r Recipes (or Slic3r CFG files) should still be under <code>C:\Users\Hyrel\AppData\Roaming\Slic3r</code>.
 +
 
 +
{| border="1" class="wikitable" style="text-align: center"
 +
|+ EcosystemApps Locations
 +
! Program Name
 +
! Executable Location
 +
|-
 +
| Slic3r EXE
 +
| <code>C:\EcosystemApps\Slic3r\slic3r.exe</code>
 +
|-
 +
| Slic3r CFG
 +
| <code>C:\Users\Hyrel\AppData\Roaming\Slic3r</code>
 +
|-
 +
| OpenSCAD
 +
| <code>C:\EcosystemApps\OpenSCAD\openscad.exe</code>
 +
|-
 +
| FreeCAD
 +
| <code>C:\EcosystemApps\FreeCAD 0.15\bin\FreeCAD.exe</code>
 +
|-
 +
| MeshLab
 +
| <code>C:\EcosystemApps\VCG\MeshLab\meshlab_32.exe</code>
 +
|-
 +
| FlatCAM
 +
| <code>C:\EcosystemApps\FlatCAM\FlatCAM.exe</code>
 +
|-
 +
| QCAD
 +
| <code>C:\EcosystemApps\QCAD\qcad.exe</code>
 +
|-
 +
| TeamViewer
 +
| <code>C:\EcosystemApps\TeamViewer\Version9\TeamViewer.exe</code>
 +
|-
 +
| InkScape
 +
| <code>C:\EcosystemApps\inkscape\inkscape.exe</code>
 +
|-
 +
| GIMP
 +
| <code>C:\EcosystemApps\GIMP 2\bin\gimp-2.8.exe</code>
 +
|}
 +
 
 +
Note that if your login ID is not "Hyrel", you'll need to adjust the location for the Slic3r cfg file appropriately. Remember to click APPLY when done to cause these settings to be applied.
 +
 
 +
== '''Head & Bed Settings''' ==
 +
 
 +
You should ALWAYS use the latest version of the settings file that you find at '''C:\Repetrel\Head Settings.'''
 +
 
 +
For Heads and Hotbeds, we now (v4) have files stored, just like head settings files. If you didn't get them, email me and I'll put the info here.
 +
 
 +
The names should be self-explanatory, with either the name of the head or the name of the printer model and bed temp:
 +
 
 +
[[File:Head_settings_folder.png]]
 +
 
 +
Right-click on the head (anywhere EXCEPT the "FLASH" button) and open the proper file for your head or bed:
 +
 
 +
[[File:Loadfromfile1.png|250px]]
 +
 
 +
And select the file for the device for which you wish to load the settings:
 +
 
 +
[[File:Loadfromfile2.png|500px]]
 +
 
 +
Please note that on some versions, the RTD type is, unfortunately, not populated. For heated heads, use "1k_PRTD" or "1K_PLAT"; for unheated heads, use "No RTD".
 +
 
 +
ESR and 30M unit beds should use "'''10K'''".
 +
 
 +
EHR and 16A unit beds should use "'''1k PRTD'''"
 +
 
 +
As with all settings, to store them as defaults, go to the last page and right-click FLASH:
 +
 
 +
[[File:Rcflash1.png|500px]]
 +
 
 +
And then click YES:
 +
 
 +
[[File:Rcflash2.png|250px]]
 +
 
 +
== '''Slicer Settings''' ==
 +
 
 +
For Slicer settings, see the [[Recipes]] page.
 +
 
 +
 
 +
== Microscope Driver ==
 +
 
 +
* Microscopes shipped since 2020 may require this driver to be downloaded, extracted, and installed: http://hyrel3d.net/downloads/drivers/Microscope_Driver_2020.rar
 +
* Microscopes shipped in 2019 and earlier may require this driver to be downloaded, extracted, and installed: http://hyrel3d.net/downloads/drivers/Microscope_Driver.rar
 +
 
 +
Please download and extract the file, then run the executable as admin, then restart the tablet or computer.

Revision as of 15:19, 22 November 2022

Printer Settings

Last, you may need to (re)load your settings; there are several screens, detailed below.

Before doing these steps, please see if the settings you already have loaded will work!

To load a configuration file, do the following:

  1. Go to Setings > Printer.
  2. Click "Save Settings To File" with your custom name, today's date, and "ASFOUND" as a backup
  3. Go see if everything works. If not:
  4. Click "Load Settings from File" - see file names below
  5. Make any customization you like
  6. Click "Flash Motion Settings"
  7. Click "Apply"
  8. Click "Save Settings To File" with your custom name, today's date, and "WORKING" as a backup
  9. Click "OK"

These steps are performed in this video: https://www.youtube.com/watch?v=N1HZOvWKqs8

Note that after flashing, or upon startup, you will be required to home the X and Y axes before other moves are allowed; on the EHR, you will also have to home the Z. This is so that the printer knows where you are and whether or not it is safe to move the amount you tell it to. If you unlock your motors or press the emergency stop button, you should home the X and Y axes again before making other movements (also Z on EHR).

While each printer is shipped with tested, verified settings, you are welcome to customize your unit. For example, a second yoke will reduce your max travel in the X; an auxiliary build plate may have smaller dimensions; tall Hydras will have more travel in the Z; and you will probably want to limit your travel if you've added a vise or chuck.

The latest Printer Settings files are available at http://hyrel3d.net/downloads/repetrel/Printer_Settings_2019.12.05.rar Note that these are included in the latest v4 Repetrel download.

File Names

When you select "Load settings from File" (or "Switch Printer Type" from the menu), here's what the file names mean:

Printer Files
File Name Model/Version Special Notes
16AS 16A Standard Standard
16AS_2Y 16A Standard 2nd Yoke
16AS_2Y_45A 16A Standard 2nd Yoke, 4th/5th Axis
16AS_45A 16A Standard 4th/5th Axis
16AT 16A Tall Standard
16AT_2Y 16A Tall 2nd Yoke
16AT_2Y_45A 16A Tall 2nd Yoke, 4th/5th Axis
16AT_45A 16A Tall 4th/5th Axis
30M_ESR 30M and ESR Standard
EHR_diffXY EHR *early models
EHR_standard EHR Standard
ESR_30M ESR, 30M Standard
30M_ESR 30M, ESR (same as above)
fadal429 Fadal CNC Standard

Programs

In Repetrel, go to the Programs tab, and double click in each text field, pointing the applications to their respective executable files under C:/EcosystemApps. See the table below for the proper locations. Note the new location for the Slic3r install; Slic3r Recipes (or Slic3r CFG files) should still be under C:\Users\Hyrel\AppData\Roaming\Slic3r.

EcosystemApps Locations
Program Name Executable Location
Slic3r EXE C:\EcosystemApps\Slic3r\slic3r.exe
Slic3r CFG C:\Users\Hyrel\AppData\Roaming\Slic3r
OpenSCAD C:\EcosystemApps\OpenSCAD\openscad.exe
FreeCAD C:\EcosystemApps\FreeCAD 0.15\bin\FreeCAD.exe
MeshLab C:\EcosystemApps\VCG\MeshLab\meshlab_32.exe
FlatCAM C:\EcosystemApps\FlatCAM\FlatCAM.exe
QCAD C:\EcosystemApps\QCAD\qcad.exe
TeamViewer C:\EcosystemApps\TeamViewer\Version9\TeamViewer.exe
InkScape C:\EcosystemApps\inkscape\inkscape.exe
GIMP C:\EcosystemApps\GIMP 2\bin\gimp-2.8.exe

Note that if your login ID is not "Hyrel", you'll need to adjust the location for the Slic3r cfg file appropriately. Remember to click APPLY when done to cause these settings to be applied.

Head & Bed Settings

You should ALWAYS use the latest version of the settings file that you find at C:\Repetrel\Head Settings.

For Heads and Hotbeds, we now (v4) have files stored, just like head settings files. If you didn't get them, email me and I'll put the info here.

The names should be self-explanatory, with either the name of the head or the name of the printer model and bed temp:

Head settings folder.png

Right-click on the head (anywhere EXCEPT the "FLASH" button) and open the proper file for your head or bed:

Loadfromfile1.png

And select the file for the device for which you wish to load the settings:

Loadfromfile2.png

Please note that on some versions, the RTD type is, unfortunately, not populated. For heated heads, use "1k_PRTD" or "1K_PLAT"; for unheated heads, use "No RTD".

ESR and 30M unit beds should use "10K".

EHR and 16A unit beds should use "1k PRTD"

As with all settings, to store them as defaults, go to the last page and right-click FLASH:

Rcflash1.png

And then click YES:

Rcflash2.png

Slicer Settings

For Slicer settings, see the Recipes page.


Microscope Driver

Please download and extract the file, then run the executable as admin, then restart the tablet or computer.