UV and Clench - Revision history

Davo: /* Connecting the Wires */

2026-09-02T19:20:21Z

‎Connecting the Wires

2026-09-02T19:20:03Z

‎Single Controller Boards

2026-03-08T16:13:47Z

‎UV Array

2025-08-11T17:42:56Z

‎Array Hardware

2025-06-06T12:41:19Z

‎UV Pen

2025-04-15T14:33:56Z

‎Array Hardware

2025-04-15T14:33:11Z

‎Array Hardware

2025-01-29T14:59:19Z

‎UV Pen

2025-01-29T14:58:55Z

‎UV Array

2025-01-29T14:58:03Z

‎Gcode

@@ Line 33: / Line 33: @@
 [[File:COD_HW.png|150px]] [[File:VCD_HW.png|150px]] [[File:KCD_HW.png|150px]]
-====== Connecting the Wires ======
+===== Connecting the Wires =====
 The next step is to ensure that the UV Array is connected to the material head circuit board.

@@ Line 20: / Line 20: @@
 ==== Single Controller Boards ====
 The first step is to ensure that the array is properly mounted:
@@ Line 30: / Line 32: @@
 [[File:COD_HW.png|150px]] [[File:VCD_HW.png|150px]] [[File:KCD_HW.png|150px]]
 The next step is to ensure that the UV Array is connected to the material head circuit board.

← Older revision		Revision as of 16:13, 8 March 2026
Line 14:		Line 14:

	The UV Arrays are set in a halo arrangement around the nozzle of the head, and they can put out a maximum of between 0.4 and 0.6 watts.		The UV Arrays are set in a halo arrangement around the nozzle of the head, and they can put out a maximum of between 0.4 and 0.6 watts.
		+
		+	While some customers have successfully attached our UV arrays to our temperature-controlled reservoir heads, we only guarantee compatibility with ambient-temperature reservoir heads.

	=== Array Hardware ===		=== Array Hardware ===

@@ Line 16: / Line 16: @@
 === Array Hardware ===
 The first step is to ensure that the array is properly mounted:
@@ Line 48: / Line 50: @@
 The D6 LED on the head's STM-103 circuit board should always be illuminated with the relative intensity of your M106 output, between 0 and 100 percent.
 === Array Gcode ===

← Older revision		Revision as of 12:41, 6 June 2025
Line 161:		Line 161:

	The UV Pens can be aimed and focused, and they will provide up to between 4 and 6 watts of power.		The UV Pens can be aimed and focused, and they will provide up to between 4 and 6 watts of power.
		+
		+	<span style="color: red;">'''Please see more details and examples for UV Arrays and UV Pens at https://hyrel3d.com/wiki/index.php/UV_and_Clench'''<br>'''PLEASE NOTE''' that the UV pen commands DO NOT WORK if you are using '''M229 E1 D1'''. You must use '''M229 E0 D0''' (NOT using E values) to use these codes.</span>

	=== Pen Hardware ===		=== Pen Hardware ===

@@ Line 31: / Line 31: @@
 Firmly but gently grasp the 18-pin connector and pull it straight away from the circuit board. You will seat the black wire in the top row, third position (marked "Gnd" on the board), and the red wire in the bottom row, second position (marked "Aux" on the board, if you can read it). This will allow the 12VDC to power the array.
-The best method to seat these crimped wires is to align the barb on the crimp up or down to point toward the plastic finger that will hold it in place. The barb is tiny, and is on the side that extends down to the wire insulation:
+The best method to seat these crimped wires is to align the barb on the crimp up or down to point toward the plastic finger that will hold it in place. The barb is tiny, and is on the side that extends down to the wire insulation (click image for larger version):
-[[File:White_connectors.png]]
+[[File:White_connectors.png|500px]]
 On your connector, since the black wire will go on the top row, the barb should be pointing up; the red wire will go on the bottom row, and the barb should be pointing down. If you pull gently on the wires, you should feel the barb catch on the plastic finger, and the wire should remain seated in the connector.

@@ Line 162: / Line 162: @@
 The UV Pens can be aimed and focused, and they will provide up to between 4 and 6 watts of power.
-=== Hardware ===
+=== Pen Hardware ===
 The pen is its own head, and is loaded into a tool position like most heads.
@@ Line 168: / Line 168: @@
 [[File:Uvata_front_sm.jpg|150px]]
-=== Gcode ===
+=== Pen Gcode ===
 Next, we need to set up the gcode to control it. The array can be used primarily in three ways. Note that there is a safety timeout, so you can't simply turn the array on and leave it on; there must be a printing (G1 with E value) move involved to use it for more than one second.

@@ Line 201: / Line 201: @@
 ==== Pen: On or Off ====
 If you want your array to turn on at a certain percentage and then turn off, you'll use an M623 to turn it on for some duration. For example:
@@ Line 218: / Line 216: @@
 ** '''P100''' (power of 100%)
 ** '''W10000''' (set watchdog timer to 10000 miliseconds (ten seconds))
    M620 T13 E1