Difference between revisions of "30M"

From Hyrel3D
Jump to: navigation, search
(Created page with "Category:Hardware Category:Printers {| align="right" | __TOC__ |} == System Models == {| border="1" class="wikitable" |+ System Model Comparison ! Model ! System 23 ...")
 
(Temperature)
Line 36: Line 36:
 
   
 
   
 
=== Temperature ===
 
=== Temperature ===
* The [[HotBed]] can be heated to any temperature up to 260°C
+
* The [[HotBed]] can be heated to any temperature up to 70°C by default, and up to 110°C if reconfigured.
 
* The [[MK-1]] can be heated to 260°C (limited life); we recommend sustained use at 250°C or below. PLA, PET, ABS and Nylon work well at 225-230°C  
 
* The [[MK-1]] can be heated to 260°C (limited life); we recommend sustained use at 250°C or below. PLA, PET, ABS and Nylon work well at 225-230°C  
 
* The [[EMO-25]] prints at room temperature
 
* The [[EMO-25]] prints at room temperature
Line 42: Line 42:
  
 
For more details about each head, see the page for that head.
 
For more details about each head, see the page for that head.
+
 
 
=== Resolution ===
 
=== Resolution ===
 
Our positional resolution is better than five microns in the X and Y (.0002”, or 2/10 of a mil or .2 mils), and better than half a micron in the Z (.0002”, or 2/100 of a mil or .02 mils)
 
Our positional resolution is better than five microns in the X and Y (.0002”, or 2/10 of a mil or .2 mils), and better than half a micron in the Z (.0002”, or 2/100 of a mil or .02 mils)

Revision as of 12:09, 7 February 2014

System Models

System Model Comparison
Model System 23 System 30
Heated Build Platform yes yes
Integrated PC
& Touchscreen
yes yes
Maximum Active Heads 4 4
Overall Height 30 31
Overall Width 26 32
Overall Depth 17 17

Technical Data

Temperature

  • The HotBed can be heated to any temperature up to 70°C by default, and up to 110°C if reconfigured.
  • The MK-1 can be heated to 260°C (limited life); we recommend sustained use at 250°C or below. PLA, PET, ABS and Nylon work well at 225-230°C
  • The EMO-25 prints at room temperature
  • The VOL-25 can be heated to 100°C

For more details about each head, see the page for that head.

Resolution

Our positional resolution is better than five microns in the X and Y (.0002”, or 2/10 of a mil or .2 mils), and better than half a micron in the Z (.0002”, or 2/100 of a mil or .02 mils)

Accuracy

Our positional accuracy is +/- 50 microns in the X and Y over an 8” travel area And +/- 20 microns in the Z over an 8” travel area

Repeatability

Our positional repeatability is about 25 microns in the X and Y (.001”, or 1 mil) And about 10 microns in the Z (.0004”, or 4/10 of a mil or .4 mils)

Layer Height

We have successfully printed in ABS with a 25µm (.025mm) layer height, but this is very time consuming.

  • We often use a 300µm (.3mm) layer height with the .5mm nozzle on the MK-1 for 1.75mm filaments.
  • We often use a 600 µm (.6mm) layer height with the 1mm nozzle on the EMO-25 for pasty extrudables.

Print Speed

The best print speed manageable (without sacrificing quality) is variable, and depends not only on the material being used and layer height, but also on how much mass is being moved in the X and Y. We normally print at 1.5m/min, or 25mm/sec with both the MK-1 and the EMO-25

Build Volume

Engines have a build volume of 200 x 200 x 200 mm.

Form Factor

Engines are 13” wide x 15” deep (plus 7” of rear space for spool rods), and are 21” tall plus heads, which can add another 10” to the height.

Adjustments

  • Speed of travel (at slicing or in g-code editor)
  • Layer thickness (at slicing)
  • Volume of flow per unit distance (at slicing or in g-code editor)
  • Extruder temperature (at slicing, in g-code editor, or manually during build) (MK-1, VOL-25)
  • Cooling Fan speed (at slicing, in g-code editor, or manually during build (MK-1, QS-1)
  • HotBed Temperature (manually, prior to or during build)