Archive

From Hyrel3D
Revision as of 12:45, 11 May 2023 by Davo (talk | contribs) (Created page with " ==Settings for Filament Heads == All printers and heads shipping after 1 Jan 2020 have shipped with some release of version 4, and these values are shown below. '''Fila...")
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search


Settings for Filament Heads

All printers and heads shipping after 1 Jan 2020 have shipped with some release of version 4, and these values are shown below.

Older settings are listed here.

Some settings for the MK-Type heads (like temperature, prime/unprime values) will vary, depending on what material you are printing with. Nozzle diameter should accurately reflect what nozzle you have loaded (0.5mm is default) AND what path width you sliced for (recipe path or extrusion width should be nozzle diameter plus 10%). Having said that, here are our default shipping settings:

Settings MK1-250, MK2-250
DISCONTINUED
MK1-450
DISCONTINUED
HT1-250 HT1-450 HT3-250 HT3-450
Material
Type (any) (any) (any) (any) (any) (any)
Color (any) (any) (any) (any) (any) (any)
Nozzle 0.500 0.500 0.500 0.500 0.500 0.500
Layer (any) (any) (any) (any) (any) (any)
Temp Info
Print Temp 240 410 240 410 240 410
Power Factor 100 100 100 100 100 100
Minimum 0 290 0 290 0 290
Maximum 250 450 250 450 250 450
Overrides
Pulses / µL 84.5 84.5 175 175  ?  ?
Multiplier 1.000 1.000 1.000 1.000 1.000 1.000
Prime
Steps 200 200 300 300  ?  ?
Rate 10,000 10,000 10,000 10,000 10,000 10,000
Dwell Time 35 35 30 30  ?  ?
Before Tool Change 2 / n/a / n/a
Unprime
Steps 200 200 300 300  ?  ?
Rate 10,000 10,000 10,000 10,000 10,000 10,000
Dwell Time -35 -35 -30 -30  ?  ?
After Tool Change 2 / n/a / n/a
Offsets
Clone Head Off Off Off Off Off Off
X 0,000 0,000 0,000 0,000 0,000 0,000
Y 0,000 0,000 0,000 0,000 0,000 0,000
Z 0,000 0,000 0,000 0,000 0,000 0,000
Head Info
Model MK1, MK2 MK450 MK1, MK2 MK450 MK1, MK2 MK450
PCB Type 4988/160J 4988/160J 4988/160J 4988/160J 4988/160J 4988/160J
RTD Type 1k_PRTD 1k_PRTD 1k_PRTD 1k_PRTD 1k_PRTD 1k_PRTD
Plot Settings (any) (any) (any) (any) (any) (any)
Motor Settings
Step Mode 16th 16th 16th 16th 16th 16th
Motor Current Normal Normal Normal Normal Normal Normal
Max Jog Rate 1,500 1,500 1,500 1,500 1,500 1,500
Rot Speed 1,500 1,500 1,500 1,500 1,500 1,500
Settings MK1-250, MK2-250 MK1-450 HT1-250 HT1-450 HT3-250 HT3-450


Settings for Reservoir Heads

All printers and heads shipping after 1 Jan 2020 have shipped with some release of version 4, and these values are shown below.

Older settings are listed here.

Some settings for the EMO-Type heads (like temperature, prime/unprime values) will vary, depending on what material you are printing with. Nozzle diameter should accurately reflect what nozzle you have loaded (1.6mm is default) AND what path width you sliced for. Temperature commands will be ignored by heads with no temperature control. Having said that, below are our default shipping settings:

METAL Reservoir Heads

Default Settings for Reservoir Heads with METAL Reservoirs
Settings EMO, VOL
27:1 Ratio
VOL
51:1 Ratio
EMO-XT, KR2, TAM
100:1
KR2-ST
Super Torque
EMO-300XT
eXtra Torque
Material
Type Custom Custom Custom Custom Custom
Color (any) (any) (any) (any) (any)
Default Nozzle 1.600 1.600 1.600 1.600 1.600
Layer (any) (any) (any) (any) (any)
Temp Info
Print Temp 0 0, 35 35 (varies) 0
Power Factor 100 100 100 100 100
Minimum 0 0 0 0 0
Maximum 0 90 0 / 180 / 270 0 0
Overrides
Pulses / µL 271.9 517 1297  ?  ?
Note: Values above in BOLD have been validated through multiple sample testing, July 2020.
Multiplier 1 1 1  ?  ?
Prime
Steps 6000 1000 6000  ?  ?
Rate 10,000 10,000 10,000  ?  ?
Dwell Time (ms) 600 100 600  ?
Unprime
Steps 6000 1000 6000  ?  ?
Rate 10,000 10,000 10,000  ?  ?
Dwell Time -600 -100 -600  ?  ?
Offsets
X 0,000 0,000 0,000 0,000 0,000
Y 0,000 0,000 0,000 0,000 0,000
Z 0,000 0,000 0,000 0,000 0,000
Head Info
Model EMO-25 VOL-25 KR2-15 or TAM-15 (varies) EMO-300XT
PCB Type 4988/160J 4988/160J 4988/160J 4988/160J 4988/160J
RTD Type 1k_PRTD 1k_PRTD 1k_PRTD 1k_PRTD 1k_PRTD
Plot Settings (any) (any) (any) (any) (any)
Motor Settings
Step Mode 16th 16th 16th 16th  ?
Motor Current Normal Normal Normal Normal  ?
Max Jog Rate 5,000 10,000 15,000  ?  ?
Rot Speed 1,500 1,500 10,000  ?  ?
Settings EMO, VOL
27:1 Ratio
VOL
51:1 Ratio
EMO-XT, KR2, TAM
100:1
KR2-ST
Super Torque
EMO-300XT
eXtra Torque

PLASTIC Reservoir Heads: Table 1

Default Settings for Reservoir Heads with PLASTIC Reservoirs - Table 1: Standard Torque, Single Reservoir
Settings SDS 1 ET SDS 5 SDS 10 SDS/HSD/RSD 30 SDS 60
Material
Type Custom Custom Custom Custom Custom
Color (any) (any) (any) (any) (any)
Default Nozzle 1.600 1.600 1.600 1.600 1.600
Layer (any) (any) (any) (any) (any)
Temp Info
Print Temp 0 0 0 0 0
Power Factor 100 100 100 100 100
Minimum 0 0 0 0 0
Maximum 0 0 0 0 / 75 / -10 0
Overrides
Pulses / µL 270 87.3 58.7 26.8 17.4
Note: Values above in BOLD have been validated through multiple sample testing, July 2020 or Oct 2021.
Multiplier 1.000 1.000 1.000 1.000 1.000
Prime
Steps 3000 1500 3000 2250 1500
Rate 10,000 10,000 10,000 10,000 10,000
Dwell Time (ms) 300 150 300 225 150
Unprime
Steps 3000 1500 3000 2250 1500
Rate 10,000 10,000 10,000 10,000 10,000
Dwell Time -300 -150 -300 -300 -300
Offsets
Clone Head Off Off Off Off Off
X 0,000 0,000 0,000 0,000 0,000
Y 0,000 0,000 0,000 0,000 0,000
Z 0,000 0,000 0,000 0,000 0,000
Head Info
Model SDS SDS-5 SDS-10 SDS-30 / HSD-30 / RSD-30 SDS-60
PCB Type 4988/160J 4988/160J 4988/160J 4988/160J 4988/160J
RTD Type None None None None / 1k_PRTD / 1k_PRTD None
Plot Settings (any) (any) (any) (any) (any)
Motor Settings
Step Mode 16th 16th 16th 16th 16th
Motor Current Normal Normal Normal Normal Normal
Max Jog Rate 10,000 10,000 10,000 10,000 10,000
Rot Speed 1500 1500 1500 1500 1500
Settings SDS 1 ET SDS 5 SDS 10 SDS/HSD/RSD 30 SDS 60

PLASTIC Reservoir Heads: Table 2

Default Settings for Reservoir Heads with PLASTIC Reservoirs - Table 2: Higher Torque and Dual Reservoir
Settings HSD-10-Ardes SDS-30-XT SDS-60-XT SDS-150-XT DSD-50
Material
Type Custom Custom Custom Custom Custom
Color (any) (any) (any) (any) (any)
Default Nozzle 1.600 1.600 1.600 1.600 4.00
Layer (any) (any) (any) (any) (any)
Temp Info
Print Temp 35 0 0 0 0
Power Factor 100 100 100 100 100
Minimum 0 0 0 0 0
Maximum 75 0 0 0 0
Overrides
Pulses / µL 1800 86 29.1 12.8 20
Note: Values above in BOLD have been validated through multiple sample testing, July 2020.
Multiplier 1.000 1.000 1.000 1.000 1.000
Prime
Steps 9000 1125 1500 1500 1
Rate 10,000 10,000 10,000 10,000 10,000
Dwell Time (ms) 900 115 150 150 1
Unprime
Steps 9000 1125 1500 1500 1
Rate 10,000 10,000 10,000 10,000 10,000
Dwell Time -900 -300 -300 -300 -100
Offsets
X 0,000 0,000 0,000 0,000 0,000
Y 0,000 0,000 0,000 0,000 0,000
Z 0,000 0,000 0,000 0,000 0,000
Head Info
Model (varies) (varies) (varies) (varies) (varies)
PCB Type 4988/160J 4988/160J 4988/160J 4988/160J 4988/160J
RTD Type 1k_PLAT_RTD None None None None
Plot Settings (any) (any) (any) (any) (any)
Motor Settings
Step Mode 16th 16th 16th 16th 16th
Motor Current Normal Normal Normal Normal Normal
Max Jog Rate 10,000 10,000 10,000 10,000 10,000
Rot Speed 7,500 1,500 1,500 1,500 1,500
Settings HSD-10-Ardes SDS-30-XT SDS-60-XT SDS-150-XT DSD-50