Filament Heads OLD

From Hyrel3D
Jump to: navigation, search

This page has settings for older version filament heads, in case users wish to remain on older software.

Settings for Filament Heads

V2: Non-Hydra units shipping through spring 2017 shipped with Repetrel version 2.x.

V3: Hydra units, and other units shipping summer 2017 through summer 2019 shipped with version 3.x, and should consult the version 3.x tables, below. All units should be upgraded to 3.x when it is available. If you run a head with v2 settings on a v3 install, the background will flash red; please make the changes below, from red to blue.

V4: All units shipping as of late summer 2019 are shipping with version 4.x, which has more fields for the heads. Please see below.

Values for versions 1.x and 2.x will be inicated in RED.
Values for version 3.x will be inicated in BLUE.
Values for version 4.x will be inicated in GREEN.
Please note that for v4, you can load settings from file.

Note that you must flash these settings to the head to make them the new default.

Some settings for the MK-Type heads (like temperature, prime/unprime values) will vary, depending on what material you are printing with. Nozzle diameter should accurately reflect what nozzle you have loaded (0.5mm is default) AND what path width you sliced for (recipe path or extrusion width should be nozzle diameter plus 10%). Having said that, here are our default shipping settings:

Settings MK1-250, MK2-250 MK1-450 HT1-250 HT1-450 HT3-250 HT3-450
Material
Type (any) (any) (any) (any) (any) (any)
Color (any) (any) (any) (any) (any) (any)
Nozzle 0.500 0.500 0.500 0.500 0.500 0.500
Layer (any) (any) (any) (any) (any) (any)
Temp Info
Print Temp 240 410 240 410 240 410
Power Factor 100 100 100 100 100 100
Minimum 0 290 0 290 0 290
Maximum 250 450 250 450 250 450
Overrides
Pulses 0.78 / 78 / 78 0.78 / 78 / 78 1.75 / 175 / 175 1.75 / 175 / 175  ?  ?
Multiplier 1.000 1.000 1.000 1.000 1.000 1.000
Prime
Steps 200 200 300 300  ?  ?
Rate 10,000 10,000 10,000 10,000 10,000 10,000
Dwell Time 20 / 35 / 35 20 / 35 / 35 20 / 35 / 30 20 / 35 / 30  ?  ?
Before Tool Change 2 / n/a / n/a
Unprime
Steps 200 200 300 300  ?  ?
Rate 10,000 10,000 10,000 10,000 10,000 10,000
Dwell Time 15 / -35 / -35 15 / -35 / -35 15 / -30 / -30 15 / -30 / -30  ?  ?
After Tool Change 2 / n/a / n/a
Offsets
Clone Head Off Off Off Off Off Off
X 0,000 0,000 0,000 0,000 0,000 0,000
Y 0,000 0,000 0,000 0,000 0,000 0,000
Z 0,000 0,000 0,000 0,000 0,000 0,000
Head Info
Model MK1, MK2 MK450 MK1, MK2 MK450 MK1, MK2 MK450
PCB Type n/a / n/a / 4988/160J
RTD Type 1k_PLAT
Motor Current High / High / n/a
Step Mode 16th / 16th / n/a
Plot Settings (any)
Motor Settings
Step Mode n/a / n/a / 16th
Motor Current n/a / n/a / Normal
Max Jog Rate n/a / n/a / 1,500
Rot Speed n/a / n/a / 1,500
Settings MK1-250, MK2-250 MK1-450 HT1-250 HT1-450 HT3-250 HT3-450