Difference between revisions of "Published Papers"

From Hyrel3D
Jump to: navigation, search
(Published in 2023)
(Count)
(2 intermediate revisions by the same user not shown)
Line 7: Line 7:
 
== Count ==
 
== Count ==
  
423 documents as of 19 May, 2023.
+
425 documents as of 30 May, 2023.
  
 
== Non-Traditional Manufacturing ==
 
== Non-Traditional Manufacturing ==
Line 471: Line 471:
 
==== Published in 2023 ====
 
==== Published in 2023 ====
  
 +
* [https://link.springer.com/article/10.1007/s10845-023-02141-0 Process Parameter Optimization for Reproducible Fabrication of Layer Porosity Quality of 3D-Printed Tissue Scaffold] by a team from several departments at [https://www.vt.edu/ Virginia Tech]
 
* [https://pubs.acs.org/doi/abs/10.1021/acsami.3c01307 Fundamentals of Crystalline Evolution and Properties of Carbon Nanotube-Reinforced Polyether Ether Ketone Nanocomposites in Fused Filament Fabrication] by a team from several departments at [https://www.tamu.edu Texas A&M University]
 
* [https://pubs.acs.org/doi/abs/10.1021/acsami.3c01307 Fundamentals of Crystalline Evolution and Properties of Carbon Nanotube-Reinforced Polyether Ether Ketone Nanocomposites in Fused Filament Fabrication] by a team from several departments at [https://www.tamu.edu Texas A&M University]
 
* [https://www.osti.gov/servlets/purl/1960414 Printed Planar Microwave Connector with Multiple Signal Lines] by a team from [https://www.uml.edu/engineering/electrical-computer/ Electrical & Computer Engineering, University of Massachusetts, Lowell]
 
* [https://www.osti.gov/servlets/purl/1960414 Printed Planar Microwave Connector with Multiple Signal Lines] by a team from [https://www.uml.edu/engineering/electrical-computer/ Electrical & Computer Engineering, University of Massachusetts, Lowell]

Revision as of 13:39, 30 May 2023

Below is a list of published works citing Hyrel equipment.

Count

425 documents as of 30 May, 2023.

Non-Traditional Manufacturing

Including Antennas, Sensors, Inductors, and Circuits; Combined Manufacturing Techniques; Electro-Spinning or Electro-Melt-Spinning or Melt Electro-Writing (MEW); 4D Printing and Shape Memory Polymers; Nanostructures; also printing with Embedded Fibers and combining FDM with DIW or MEW.

Published in 2023

Published in 2022

Published in 2021

Published in 2020

Published in 2019

Published in 2018

Published in 2017

Published in 2016

Published in 2015

Unheated or Chilled Reservoir Printing (DIW)

Also known as Robocasting or DIW (Direct Ink Writing).

Published in 2023

Published in 2022

Published in 2021

Published in 2020

Published in 2019

Published in 2018

Published in 2017

Published in 2016

Published in 2015

Published in 2014

Heated Reservoir Printing (DPE, HME)

Also known as DPE (Direct Powder Extrusion) or HME (Hot Melt Extrusion).

Published in 2023

Published in 2022

Published in 2021

Published in 2020

Published in 2019

Published in 2018

Published in 2017

Filament Printing (HME, FFF, FDM)

Also known as HME (Hot Melt Extrusion), FFF (Fused Filament Fabrication), or FDM (Fused Deposition Modeling).

Published in 2023

Published in 2022

Published in 2021

Published in 2020

Published in 2019

Published in 2018

Published in 2017

Published in 2016