|
|
| Line 1: |
Line 1: |
| − | [[Category:Gcode]] | + | #REDIRECT [[Gcode]] |
| − | {| align="right"
| |
| − | | __TOC__
| |
| − | |}
| |
| − | | |
| − | =====NOTE: THIS PAGE IS FOR VERSION 1.85=====
| |
| − | | |
| − | == Start Gcode ==
| |
| − | | |
| − | This code should be at the beginning of every Gcode file:
| |
| − | | |
| − | <nowiki>
| |
| − | M757 S[nozzle_diameter] ;set layer/path width
| |
| − | M729 S3 ;set 16 step mode
| |
| − | M758 S0.095 ;set steps/nL
| |
| − | M734 F60 ;set error reporting interval for redundant errors to every 60 seconds
| |
| − | ;--------------------</nowiki>
| |
| − | | |
| − | == End Gcode ==
| |
| − | | |
| − | This code should be at the end of every Gcode file:
| |
| − | | |
| − | <nowiki>
| |
| − | ;--------------------
| |
| − | ;M721 ;unprime
| |
| − | M103 ;stop extrusion
| |
| − | M104 T10 S0 ;turn off all extruders
| |
| − | M140 S0 ;turn off hotbed</nowiki>
| |
| − | | |
| − | == Layer Changes ==
| |
| − | | |
| − | Please also note, that if you want to take advantage of several new features regarding
| |
| − | layer change options, ( I.E. pause at end of layer, take picture, etc)
| |
| − | you will want to add the M790 to the layer change G-Code as well:
| |
| − | | |
| − | <nowiki>
| |
| − | M790 ;announce new layer</nowiki>
| |
| − | | |
| − | == Everything ==
| |
| − | | |
| − | Here is code that should be in EVERY recipe:
| |
| − | | |
| − | <nowiki>
| |
| − | ;now we set up for any build offsets that we may want
| |
| − | G21 ; use millimeters
| |
| − | G90 ; absolute coordinates
| |
| − | G0 Z5 ; lift head to avoid collisions
| |
| − | G28 X0 Y0 ;always home before starting a build home X and Y
| |
| − | G0 X0 Y0 ; move to desired origin, necessary if you want a negative offset
| |
| − | G92 X0 Y0 ; reset origin:to new X and Y, it is legal to add values to x an y, I.e. X30 Y40 will
| |
| − | ;set the current location to X30 an Y40
| |
| − | M83 ; relative extruder coordinates
| |
| − | | |
| − | ;set up Head Flow characteristics
| |
| − | M6 T10 ; select all heads on yoke 1
| |
| − | ;M227 ; enable unprime/prime on non printing moves
| |
| − | M221 S1.0 ; set fudge factor for extruder to 1.0
| |
| − | M756 S[first_layer_height] ; set first layer thickness
| |
| − | M757 S[nozzle_diameter] ; set layer/path width
| |
| − | M729 S3 ; set 16 step mode
| |
| − | ;set the pulses per unit volume, this is different depending on extruder type
| |
| − | ;and material size, I.e if the 1.75mm filament is really 1.65, you can adjust this number
| |
| − | ;Or the Fudge factor M221 to get the correct amount of material.
| |
| − | M758 S0.095 ; set steps/nL</nowiki>
| |
| − | | |
| − | Typical S values for M758:
| |
| − | <nowiki>
| |
| − | MK-1 ABS 1.75mm .09-.12
| |
| − | EMO-25 Plasticine .06</nowiki>
| |
