Difference between revisions of "Materials"
(→Materials Printable on Hyrel Machines) |
|||
| Line 68: | Line 68: | ||
| [[EMO-25]], 19:1 <br/> [[EMO-25]], 27:1 || n/a || n/a || n/a || 1.75 <br/> 2.30 || yes | | [[EMO-25]], 19:1 <br/> [[EMO-25]], 27:1 || n/a || n/a || n/a || 1.75 <br/> 2.30 || yes | ||
|- | |- | ||
| − | ! [http://www.hasbro.com/playdoh/en_AU/ | + | ! [http://www.hasbro.com/playdoh/en_AU/ Play-Doh] |
| [[EMO-25]], 19:1 <br/> [[EMO-25]], 27:1 || n/a || n/a || n/a || 1.75 <br/> 2.30 || yes | | [[EMO-25]], 19:1 <br/> [[EMO-25]], 27:1 || n/a || n/a || n/a || 1.75 <br/> 2.30 || yes | ||
|- | |- | ||
Revision as of 12:39, 4 May 2015
A huge variety of materials can be printed with various extruders on the Hyrel machines. Below are the recipes we have so far...
Materials Printable on Hyrel Machines
The following is a list of materials with which the Hyrel machines can print; you can sort by any column:
| Material | Extruder | HotHead (°C) | Fan Speed* | HotBed (°C) | Steps / nl | Verified? |
|---|---|---|---|---|---|---|
| ABS | MK1-250 | 240/235 | 35 (=89%) | 80 | 0.78 | yes |
| PLA | MK1-250 | 185/180 | 35 (=89%) | 40 | 0.78 | yes |
| PlastInk Rubber | MK1-250 | 225 | 35 (=89%) | 50 | 0.78 | yes |
| NinjaFlex | MK1-250 | 225 | 35 (=89%) | 50 | 0.78 | yes |
| Nylon | MK1-250 | 225 | 35 (=89%) | 80 | 0.78 | yes |
| T-Glase | MK1-250 | 225 | 35 (=89%) | 80 | 0.78 | yes |
| BendLay | MK1-250 | 225 | 35 (=89%) | 50 | 0.78 | no |
| LayBrick | MK1-250 | 225 | 35 (=89%) | 80 | 0.78 | no |
| LayWoo-d3 | MK1-250 | 220/205 | 35 (=89%) | 80 | 0.78 | yes |
| PET | MK1-250 | 210 | 35 (=89%) | 40 | 0.78 | no |
| PVA | MK1-250 | 210 | 35 (=89%) | 40 | 0.78 | no |
| Clay | EMO-25, 19:1 EMO-25, 27:1 |
n/a | n/a | n/a | 1.75 2.30 |
yes |
| Metal Clay, Precious Metal Clay |
EMO-25, 19:1 EMO-25, 27:1 |
n/a | n/a | n/a | 1.75 2.30 |
yes |
| Polypropylene | MK1-250 | 235 | 35 (=89%) | 80 | 0.78 | yes |
| Polycarbonate | MK1-350 | 350 | 35 (=89%) | 80 | 0.78 | yes |
| Porcelain | EMO-25, 19:1 EMO-25, 27:1 |
n/a | n/a | n/a | 1.75 2.30 |
yes |
| Plasticine | EMO-25, 19:1 EMO-25, 27:1 |
n/a | n/a | n/a | 1.75 2.30 |
yes |
| Play-Doh | EMO-25, 19:1 EMO-25, 27:1 |
n/a | n/a | n/a | 1.75 2.30 |
yes |
| Sculpey | EMO-25, 19:1 EMO-25, 27:1 |
n/a | n/a | n/a | 1.75 2.30 |
yes |
| Sugru | EMO-25, 19:1 EMO-25, 27:1 |
n/a | n/a | n/a | 1.75 2.30 |
yes |
| RTV Silicone | EMO-25, 19:1 EMO-25, 27:1 |
n/a | n/a | n/a | 1.75 2.30 |
yes |
- Note: Be sure the fan directs air to the material and not directly at the nozzle.
- Note: In Repetrel 1.85, you should slice with a fan value between 0 and 39, which will result in a fan speed between 0 and 99, since we have our fans run between 0 and 100, not between 0 and 255 like other printers.
