Difference between revisions of "Emulsifiables"
| Line 30: | Line 30: | ||
! UV Crosslinking | ! UV Crosslinking | ||
| no || yes || no || yes || no || yes | | no || yes || no || yes || no || yes | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
|} | |} | ||
As of 16 Nov, the latest firmware is 32V, included with Repetrel 2.828. | As of 16 Nov, the latest firmware is 32V, included with Repetrel 2.828. | ||
| − | |||
Some settings for the EMO-Type heads (like temperature, prime/unprime values) will vary, depending on what material you are printing with. Nozzle diameter should accurately reflect what nozzle you have loaded (1.6mm is default) AND what path width you sliced for. Temperature commands will be ignored by heads with no temperature control. Having said that, here are our default shipping settings: | Some settings for the EMO-Type heads (like temperature, prime/unprime values) will vary, depending on what material you are printing with. Nozzle diameter should accurately reflect what nozzle you have loaded (1.6mm is default) AND what path width you sliced for. Temperature commands will be ignored by heads with no temperature control. Having said that, here are our default shipping settings: | ||
Revision as of 14:38, 8 December 2015
EMO-Type heads are for printing as follows:
- With pastes, gels, emulsifiables or waxes.
- At room or elevated temperatures.
- With or without UV Crosslining.
- With Hyrel Nozzles (1.5mm, 2mm) or Luer Tips.
These include the following:
| Model | EMO-25 | COD-25 | VOL-25 | VCD-25 | KRA-15 | KCD-15 |
|---|---|---|---|---|---|---|
| Max Temp | Ambient | Ambient | 100°C | 100°C | 150°C | 150°C |
| UV Crosslinking | no | yes | no | yes | no | yes |
As of 16 Nov, the latest firmware is 32V, included with Repetrel 2.828.
Some settings for the EMO-Type heads (like temperature, prime/unprime values) will vary, depending on what material you are printing with. Nozzle diameter should accurately reflect what nozzle you have loaded (1.6mm is default) AND what path width you sliced for. Temperature commands will be ignored by heads with no temperature control. Having said that, here are our default shipping settings:
| Settings: | 19:1 Ratio: | 27:1 Ratio: | 51:1 Ratio: | 100:1 Ratio: |
|---|---|---|---|---|
| Material | ||||
| Type | (any) | (any) | (any) | (any) |
| Color | (any) | (any) | (any) | (any) |
| Nozzle | 1.600 | 1.600 | 1.600 | 1.600 |
| Layer | (any) | (any) | (any) | (any) |
| Temp Info | ||||
| Print Temp | 30 | 30 | 30 | 30 |
| Power Factor | 100 | 100 | 100 | 100 |
| Minimum | (any) | (any) | (any) | (any) |
| Maximum | (any) | (any) | (any) | (any) |
| Overrides | ||||
| Pulses | 1.600 | 2.300 | 4.700 | 8.750 |
| Feed Rate % | 1.000 | 1.000 | 1.000 | 1.000 |
| Prime | ||||
| Steps | 500 | 700 | 900 | 2000 |
| Rate | 10,000 | 10,000 | 10,000 | 10,000 |
| Dwell Time (ms) | 100 | 100 | 110 | 120 |
| Before Tool Change | 1 | 1 | 1 | 1 |
| Unprime | ||||
| Steps | 400 | 550 | 750 | 1600 |
| Rate | 10,000 | 10,000 | 10,000 | 10,000 |
| Dwell Time (ms) | 100 | 100 | 100 | 110 |
| After Tool Change | 1 | 1 | 1 | 1 |
| Offsets | ||||
| Clone Head | Off | Off | Off | Off |
| X | 0,000 | 0,000 | 0,000 | 0,000 |
| Y | 0,000 | 0,000 | 0,000 | 0,000 |
| Z | 0,000 | 0,000 | 0,000 | 0,000 |
| Head Info | ||||
| Model | (varies) | (varies) | (varies) | (varies) |
| RTD Type | 1 Meg | 1 Meg | 1 Meg | 1 Meg |
| Motor Current | High | High | High | High |
| Step Mode | Sixteenth | Sixteenth | Sixteenth | Sixteenth |
