Difference between revisions of "Main Page"
(→Hot Flow) |
|||
| Line 207: | Line 207: | ||
{| border="1" class="wikitable sortable" style="width: 85%;" | {| border="1" class="wikitable sortable" style="width: 85%;" | ||
|+ Cold Flow Head Properties | |+ Cold Flow Head Properties | ||
| − | ! style="width: | + | ! style="width: 10%;" | Head |
| − | ! style="width: | + | ! style="width: 10%;" | Min Temp |
| − | ! style="width: | + | ! style="width: 10%;" | Max Temp |
| − | ! style="width: | + | ! style="width: 10%;" | Filament Type |
| − | ! style="width: | + | ! style="width: 10%;" | Nozzle |
| + | ! style="width: 20%;" | Recommended For | ||
|- | |- | ||
! [[MK1-250]] | ! [[MK1-250]] | ||
| Line 218: | Line 219: | ||
| Standard | | Standard | ||
| .35mm, .50mm, .75mm, 1.0mm | | .35mm, .50mm, .75mm, 1.0mm | ||
| + | | ABS, LayBrick, LayWood, Nylon PC, PET, PETG, PETT, PLA, PP, PVA, T-Glase | ||
|- | |- | ||
! [[MK2-250]] | ! [[MK2-250]] | ||
| Line 224: | Line 226: | ||
| Flexible | | Flexible | ||
| .35mm, .50mm, .75mm, 1.0mm | | .35mm, .50mm, .75mm, 1.0mm | ||
| + | | BendLay, FilaFlex, Flex45, NinjaFlex, PlastInk Rubber | ||
|- | |- | ||
! [[MK1-450]] | ! [[MK1-450]] | ||
| Line 230: | Line 233: | ||
| Engineering | | Engineering | ||
| .50mm | | .50mm | ||
| + | | PC, PEEK | ||
|- | |- | ||
|} | |} | ||
Revision as of 15:34, 28 January 2016
Welcome to the Hyrel Wiki.
Printers
As of Jan, 2016, Hyrel Printers are available in two models: Engines and Systems.
- Engines are open-air models. Detailed information is on the Engines page.
- Systems are enclosed models. Detailed information is on the Systems page.
Filaments, Heads and Flow
We break down our deposition methods based on temperature, as follows:
Cold Flow
Cold Flow means fluid (non-filament-based) materials which are deposited at room temperature, with or without UV Crosslinking.
Materials, Cold Flow
- 3P Quick Cure Clay
- Adhesives
- Clay
- Epoxy, Two-part
- Fimo
- Glue
- Kato
- Metal Clay, including Precious Metal Clay (PMC)
- Modeling Clay
- PEG
- Porcelain
- Plasticine
- Play-Doh
- Resins
- RTV Silicone
- Sculpey
- Sugru
Heads, Cold Flow
| Head | Container | Capacity | Nozzle | UV Crosslinking |
|---|---|---|---|---|
| EMO-25 | Aluminum | 25cc | 1.5mm, 2.0mm, Luer | No |
| COD-25 | Aluminum | 25cc | Luer | Yes |
| SDS-5 | Syringe | 05cc | Luer | No |
| CSD-5 | Syringe | 05cc | Luer | Yes |
| SDS-10 | Syringe | 10cc | Luer | No |
| CSD-10 | Syringe | 10cc | Luer | Yes |
| SDS-30 | Syringe | 30cc | Luer | No |
| CSD-30 | Syringe | 30cc | Luer | Yes |
| SDS-60 | Syringe | 60cc | Luer | No |
| CSD-60 | Syringe | 60cc | Luer | Yes |
Warm Flow
Warm Flow means fluid (non-filament-based) materials which are deposited at up to 100°C, with or without UV Crosslinking.
Materials, Warm Flow
Note that some materials (like Fimo, Plasticine and Sculpey) flow more freely when slightly above room temperature, and perhaps too freely at higher temperatures.
Heads, Warm Flow
| Head | Max Temp | Container | Capacity | Nozzle | UV Crosslinking |
|---|---|---|---|---|---|
| VOL-25 | 100°C | Aluminum | 25cc | 1.5mm, 2.0mm, Luer | No |
| VCD-25 | 100°C | Aluminum | 25cc | Luer | Yes |
| KRA-15 | 150°C | Stainless | 15cc | 1.5mm, 2mm, Luer | No |
| KCD-15 | 150°C | Stainless | 15cc | Luer | Yes |
Hot Flow
Hot Flow means 1.75mm diameter, filament-based materials which are deposited at up to 250°C, with
Materials, Hot Flow
Heads, Hot Flow
| Head | Min Temp | Max Temp | Filament Type | Nozzle | Recommended For |
|---|---|---|---|---|---|
| MK1-250 | 150°C | 250°C | Standard | .35mm, .50mm, .75mm, 1.0mm | ABS, LayBrick, LayWood, Nylon PC, PET, PETG, PETT, PLA, PP, PVA, T-Glase |
| MK2-250 | 150°C | 250°C | Flexible | .35mm, .50mm, .75mm, 1.0mm | BendLay, FilaFlex, Flex45, NinjaFlex, PlastInk Rubber |
| MK1-450 | 250°C | 450°C | Engineering | .50mm | PC, PEEK |
